plcforum.uz.ua

International PLC Forum
It is currently Wed Oct 22, 2014 3:10 pm

All times are UTC + 3 hours




Post new topic Reply to topic  [ 15 posts ] 
Author Message
PostPosted: Fri Dec 28, 2007 12:06 pm 

Joined: Sat Dec 08, 2007 7:22 pm
Posts: 15
Location: Europe
Hi folks!

I need to convert a Modsoft ladder logic to Unity Pro.
I need the tool to convert the Modsoft ladder logic. This tool is installed separately, but after installation is part of the Unity Pro software. (It's a kind of add-on to Unity Pro).

Thanks,
Marosy


Top
 Profile  
 
 Post subject:
PostPosted: Fri Dec 28, 2007 7:13 pm 
Site Admin

Joined: Wed Sep 06, 2006 3:03 pm
Posts: 967
Location: CIS
Try to use old Modsoft Converter (that is a part of Concept) and then import results to Unity Pro.


Top
 Profile  
 
 Post subject:
PostPosted: Sat Dec 29, 2007 1:30 pm 

Joined: Sat Dec 08, 2007 7:22 pm
Posts: 15
Location: Europe
Schtiel,

Thanks, but Unity Pro doesn't handle the Concept LL984 ladder logic. It can't convert. I tried what you said.
I suppose the Modsoft to Unity Pro conversion tool is located on the Unity Pro installation CD. (I have only the demo version without the conversion tool.)
So if someone has the official Unity Pro installation CD, It would be really nice to upload the conversion tool to rapidshare.

Regards,
Marosy


Top
 Profile  
 
 Post subject:
PostPosted: Sat Dec 29, 2007 2:15 pm 

Joined: Sat Oct 22, 2005 10:17 am
Posts: 431
Location: Europe
read this post

viewtopic.php?t=6855&highlight=unity

most


Top
 Profile  
 
 Post subject:
PostPosted: Sat Dec 29, 2007 4:12 pm 

Joined: Sat Dec 08, 2007 7:22 pm
Posts: 15
Location: Europe
Thanks, but I have that exact version of Unity Pro.
It doesn't have the conversion tool.
It could be that the tool is available in a separate kit?


Top
 Profile  
 
 Post subject:
PostPosted: Mon Dec 31, 2007 12:33 am 
Site Admin

Joined: Wed Sep 06, 2006 3:03 pm
Posts: 967
Location: CIS
I have an official version of Unity Pro (4 or 5 CDs). I'll look for the required tool after New Year.


Top
 Profile  
 
 Post subject:
PostPosted: Mon Dec 31, 2007 9:22 pm 

Joined: Sat Dec 08, 2007 7:22 pm
Posts: 15
Location: Europe
Schtiel,
Thanks and Happy New Year!


Top
 Profile  
 
 Post subject:
PostPosted: Sun Jan 13, 2008 10:19 am 

Joined: Sat Dec 08, 2007 7:22 pm
Posts: 15
Location: Europe
I'm still looking for the Modsoft to Unity Pro (984LL to Unity) conversion tool. Please help.


Top
 Profile  
 
 Post subject:
PostPosted: Mon Jan 14, 2008 5:54 pm 
Site Admin

Joined: Wed Sep 06, 2006 3:03 pm
Posts: 967
Location: CIS
There is no conversion dll on Unity 2.3 CDs :-(

I found here that conversion tools you need are available in the new version of Unity - v 3.1:
http://download.telemecanique.com/C1257 ... 000_03.pdf

As for earlier versions - this dll is possibly available upon request to Schneider...


Top
 Profile  
 
 Post subject:
PostPosted: Tue Jan 15, 2008 6:42 pm 

Joined: Sat Dec 08, 2007 7:22 pm
Posts: 15
Location: Europe
Schtiel,
Thanks for the reply.
I guess in Unity Pro 3.1 it's setup option.
Regards,
Marosy


Top
 Profile  
 
PostPosted: Tue Jan 19, 2010 6:11 pm 

Joined: Fri May 01, 2009 11:50 am
Posts: 111
Dear Friends,

I also need the ModSoft to Unity Pro Conversion tool, as per previous discussion. I have gone through the Unity Pro V3.1, But didn't found the ModSoft Conversion tool. Unity Pro V3.1 has PL7 to Unity & concept to Unity conversion tool.

I need your help. If you could suggest me the best possible way to convert ModSoft Application to Unity Pro.

Regards

LEO


Top
 Profile  
 
PostPosted: Wed Jan 20, 2010 4:02 am 

Joined: Sat Oct 22, 2005 10:17 am
Posts: 431
Location: Europe
leofarhan wrote:
also need the ModSoft to Unity Pro Conversion tool,


with unity V4
read this document with attention
http://www.megaupload.com/?d=B0FYYTZ5
.......use the LL984 to Unity Converter directly via the Unity Pro menu File → Open......
try and say if works
Image


Top
 Profile  
 
PostPosted: Wed Jan 20, 2010 10:29 pm 

Joined: Fri May 01, 2009 11:50 am
Posts: 111
Dear Most,

While conversion of the Applicaition (either from modsoft or ProWorX) I recieved the following errors.


"Conversion of file C\Documents and Settings\Administrator\Desktop\ModSoft_Application.pwx
Converter DLL for this extension not found. Please install it."


Similarly error for ProWorx application.

Then I realize that I have to check Converters in the Option Management.

Further I checked and found that during installation there are two available conveters i.e. Concept & PL7.

Still I can not upgrad my application. If found through some sources that Schneider that Schneider have this conversion tool, and it not for sale, therefore this conversion tool is not available.

Regards

Leo-Ali


Top
 Profile  
 
PostPosted: Thu Jan 21, 2010 12:35 am 

Joined: Sat Oct 22, 2005 10:17 am
Posts: 431
Location: Europe
leofarhan wrote:

While conversion of the Applicaition (either from modsoft or ProWorX) I recieved the following errors.
"Conversion of file C\Documents and Settings\Administrator\Desktop\ModSoft_Application.pwx
Converter DLL for this extension not found. Please install it."

Similarly error for ProWorx application.


olá leofarhan
I only tested with proworx, I think that work well, see the pictures
my program is V4 by http://www.area51warez.info/softwares/3 ... l-v40.html
i not test with hardware

Image


Last edited by most on Fri Jan 22, 2010 2:48 am, edited 1 time in total.

Top
 Profile  
 
PostPosted: Fri Jan 22, 2010 2:46 am 

Joined: Sat Oct 22, 2005 10:17 am
Posts: 431
Location: Europe
most wrote:
leofarhan wrote:

While conversion of the Applicaition (either from modsoft or ProWorX) I recieved the following errors.
"Conversion of file C\Documents and Settings\Administrator\Desktop\ModSoft_Application.pwx
Converter DLL for this extension not found. Please install it."

Similarly error for ProWorx application.


for modsoft
I have made some tests, tries in this way
install concept xl 2.6, this program have one tool called Modsoft Convert
open your file *.ENV
save in *.PRJ
Now open another tool Concept Convert
convert your *.prj, another file appears.*.asc
open Unity and open *.asc, also in "tools" open "convert partially" this file *.asc
you see the converter working, but now, I think that it is necessary to configure i/o
I am correct, or not :?:


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 15 posts ] 

All times are UTC + 3 hours


Who is online

Users browsing this forum: No registered users and 5 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum

Search for:
Jump to:  
Powered by International PLCforum® Forum Software © PLCforum
Mobile version