Siemens Touch panel

ProTool, WinCC flexible, WinCC, PP/OP/TP/TD/MP
Post Reply
omar zedan
Posts: 236
Joined: Sat Oct 22, 2011 7:12 am

Siemens Touch panel

Post by omar zedan » Wed Jan 02, 2013 8:30 pm

Dear All
I use wincc flexible 2008 to built a project for a touch panel 377 12" ,
The Wincc Flexible
Version 2008
Build V1.3.0.0_1.83.0.1

The panel order number 6AV6 644-0AA01-2AX0

When I use Transfere the program ask me to update the OS of the device
When I use Transfere the OS Update the Message
"Cannot perform Restore opertion. Backed up file(s) not compatible with the operating unit.
(not_allow)
Check the operating system version and hardware configuration of operating unit"
What Can I do to fix this problem????
Thanks

CoMod
Site Admin
Posts: 3971
Joined: Thu Feb 16, 2006 3:25 pm
Location: Russia
Contact:

Re: Siemens Touch panel

Post by CoMod » Thu Jan 03, 2013 6:44 pm

1. Archive project to ZIP
2. Install SP3 and update 3 for SP3
Build=1.4.3.0
viewtopic.php?f=36&t=8650&p=57737#p57737
http://rutracker.org/forum/viewtopic.php?t=3957237
Image

omar zedan
Posts: 236
Joined: Sat Oct 22, 2011 7:12 am

Re: Siemens Touch panel

Post by omar zedan » Thu Jan 03, 2013 7:39 pm

Thanks
I will try it.

omar zedan
Posts: 236
Joined: Sat Oct 22, 2011 7:12 am

Re: Siemens Touch panel

Post by omar zedan » Fri Jan 04, 2013 8:00 pm

Dear CoMod
I install winccfex 2008 SP3 and update 3
and the version become
Version 2008 sp3 upd3
build k01.04.00.03_01.05.00.09

and the problem still the same
Thanks

CoMod
Site Admin
Posts: 3971
Joined: Thu Feb 16, 2006 3:25 pm
Location: Russia
Contact:

Re: Siemens Touch panel

Post by CoMod » Fri Jan 04, 2013 9:46 pm

Photo of panel label ?
Image

omar zedan
Posts: 236
Joined: Sat Oct 22, 2011 7:12 am

Re: Siemens Touch panel

Post by omar zedan » Sat Jan 05, 2013 9:36 am

Dear CoMod
unfortunately I stick in this factory in very far place from cities and I have not camera therefore I wrote evry letter in the panel plate.

SIMENS
MP 377 12" Touch
1p 6AV6 644-0AA01-2AX0
S C-C2C73948
MAC-ADD.:00-1B-1B-1C-DA-79
APPROVED
CL.I,DIV.2GP.A,B,C,DT4
Type 4X/12 INDOOR ONLY
II3D Ex tD A22 IP66 T70
KEMA 06 ATEX0266X
EStand:11
Made in Germany
--------------------
Listed 3DA1
IND.CONT.EQ. For Haz.Loc.:
LC.I,DIV.2GP.A,B,C,D T4
LC.I,Zone 2,GP.IIC,T4
Encloser type 4x,Type 12
Indoor use only, Watertight
Input DC 24/1.8A max
KCC-REM-S49-HMI
Ta: 0C..+50C Vertical

Thanks

CoMod
Site Admin
Posts: 3971
Joined: Thu Feb 16, 2006 3:25 pm
Location: Russia
Contact:

Re: Siemens Touch panel

Post by CoMod » Sat Jan 05, 2013 12:16 pm

http://support.automation.siemens.com/W ... en/5827904
Warning: transfer of the configuration via MPI/PROFIBUS
If the operating system of the panel is already compatible with the version of ProTool used, you must check the MPI/PROFIBUS addresses used of the PG and panel.
If the panel and the PG happen to have the identical MPI/PROFIBUS address, the transfer is also aborted with the message described.
Image
ProTool = Flexible

omar zedan
Posts: 236
Joined: Sat Oct 22, 2011 7:12 am

Re: Siemens Touch panel

Post by omar zedan » Sun Jan 06, 2013 5:11 pm

Dear CoMod
I use ethernet port in my laptop with address 192.168.1.70 and I set the IP address of the panel to 192.168.1.1 and I ping it and there is areplay. and I didnot use MPI address.
What can I do know????
Thanks

omar zedan
Posts: 236
Joined: Sat Oct 22, 2011 7:12 am

Re: Siemens Touch panel

Post by omar zedan » Sun Jan 06, 2013 5:14 pm

Dear CoMode
I use MPI addapter with address 0 and select the MPI address of panel 12 and the problem still the same.
Sorry to boring you but I appreciate your helping so much.
Thanks

Post Reply