plcforum.uz.ua
http://plcforum.uz.ua/

Need firmware for Danfoss FC302
http://plcforum.uz.ua/viewtopic.php?f=16&t=25767
Page 1 of 1

Author:  Xenonci [ Sat Jan 06, 2018 5:03 pm ]
Post subject:  Need firmware for Danfoss FC302

Hi Guys,

I need to roll back firmware into Danfoss FC302 inverter. Now it is 40.05. I need version 4.38 or earlier.
Where I can find firmware images (files *.ose or *.osx) firmware in Danfoss FC302 using software MCT ?

Author:  mohdabshr [ Sun Jan 07, 2018 6:39 am ]
Post subject:  Re: Need firmware for Danfoss FC302

In MCT use converter to change firmware and download to FC302.

Author:  Xenonci [ Sun Jan 07, 2018 1:45 pm ]
Post subject:  Re: Need firmware for Danfoss FC302

What is the menu item in the mct 10 for this?
How to download the firmware from the danfoss drive for convert???

Author:  mohdabshr [ Sun Jan 07, 2018 4:18 pm ]
Post subject:  Re: Need firmware for Danfoss FC302

Hi after you opened your project with MCT right click mouse on the project you will see in the menu convert drive.

Thanks

Author:  Xenonci [ Tue Jan 09, 2018 1:21 pm ]
Post subject:  Re: Need firmware for Danfoss FC302

Hi
When I try to write to the drive the project from an early version 4.38 it fails with the following message. Version 5.84 does not overwrite. :( :(

Image

Author:  mohdabshr [ Tue Jan 09, 2018 2:02 pm ]
Post subject:  Re: Need firmware for Danfoss FC302

Hi in your project you didn't change the voltage to be 380-500 volt and you didn't choose the option A this is reason.

Author:  Xenonci [ Tue Jan 09, 2018 4:12 pm ]
Post subject:  Re: Need firmware for Danfoss FC302

I have adjusted the tension and removed the option. Version 4.38 is not rewritten 5.84. Project loaded good, but in paragraph 15.43 are still version software 05.84.


Image

Author:  mohdabshr [ Tue Jan 09, 2018 9:05 pm ]
Post subject:  Re: Need firmware for Danfoss FC302

Hi what is the reason you want to change the firmware of the drive to 4.38.

Author:  Xenonci [ Wed Jan 10, 2018 6:50 pm ]
Post subject:  Re: Need firmware for Danfoss FC302

Hi
Because the controller omron CJ1-M not familiar with the danfoss 4.38 above. Error "no connection". Program the controller to change there is no possibility

Author:  mohdabshr [ Thu Jan 11, 2018 8:34 pm ]
Post subject:  Re: Need firmware for Danfoss FC302

Hi my friend I think the firmware not effect the communication between fc302 and plc you must check setting and wiring , what is the communication between fc302 and plc .

Author:  Xenonci [ Sat Jan 13, 2018 10:35 am ]
Post subject:  Re: Need firmware for Danfoss FC302

Hi.
When I put outside instead of the frequency Converter Converter firmware 4.38 it works in that place. When I put any other Converter with firmware older than 4.38 - it doesn't work. Meanwhile, they all meet in the fc Protocol when communicating with the laptop.Now I am trying to connect the old inverter VLT5000 FC302 instead.

Page 1 of 1 All times are UTC + 3 hours
Powered by phpBB® Forum Software © phpBB Group
http://www.phpbb.com/