What has Changed Compared to Version STEP 7 V5.6 SP2?
HW Config
• Adding connections via command interface has been improved.
• The configuration of Safety modules via GSD has been improved.
• It is now once again possible to configure I devices in shared mode.
• Restricted use of scripts in the STEP 7 command interface on Windows 10
Due to thread synchronization problems when automatically saving STEP 7 user data, Visual Basic script applications can experience sporadic crashes (possibly with data loss). Therefore, the command interface is currently only partially suitable for such applications. Unpredictable errors can occur, especially with nested loop operations. It is highly recommended that you avoid such use cases and use Visual Basic scripts only with care and caution.
• As of this Hotfix: When uploading certain device configurations, the IP address was corrupted. This has now been corrected.
Programming LAD/STL/FBD blocks
• The function "Check and Update Accesses" has been improved.
HW Config
• Adding connections via command interface has been improved.
• As of this Hotfix: The configuration of Safety modules via GSD has been improved.
• As of this Hotfix: It is now once again possible to configure I devices in shared mode.
Programming LAD/STL/FBD blocks
• The function "Check and Update Accesses" has been improved.
It has S7-BlockPrivacy inside and FM Configuration Package (like fm-x50), CP PtP-Param in Optional Components, but no s7-scl and modbus.
So we are just waiting for Professional version (with s7-scl, s7-graph, s7-plcsim).
If some good guy know the information, please share. Thank you.
About keys and Sim_EKB_Install - Здесь говорить о ключах viewtopic.php?f=30&t=218
нужен экран АЛМ с установленными ключами
возможно ты попал на коллизию с ключом на Проф 5.6 - надо ставить Проф ключ для Портала 14.1 или 15.0
STEP7 v5.6 Basis license: WORKS
STEP7 v5.6 Professional license: DOES NOT WORK
STEP7 v14 Professional Combo license: DOES NOT WORK
yes... valid key for STEP7 v14.1 Professional / для STEP7 PROFESSIONAL 2017 подходит ключ от v14.1
see New keys folder / смотрите ключ в папке Новые ключи
[/quote]
в последующих ЕКБ коллизия поправлена
What has Changed hotfix 1 for STEP 7 V5.6 Compared to Version STEP 7 V5.6?
Installation of hotfix 1 for STEP 7 V5.6
As of this hotfix: If after installing a hotfix 1 for STEP 7 V5.6 the original installation is changed with "Change program" or "Repair program" the hotfix needs to be installed again.
HW Config
Ab diesem Hotfix: In a configuration that uses the function "Use different method to obtain IP address" there is no longer a warning relating to the NTP server address and another subnet.
SIMATIC Manager
As of this hotfix: The display of the object size of objects larger than 2 GB has been improved.
Report System Errors
As of this hotfix: A battery fault is also displayed for a CPU if this is operated in a non-redundant configuration.
Re: [LINK]: STEP 7 V5.6 HF1 Professional version 2017
Posted: Sun Aug 13, 2017 9:05 pm
by CoMod
maybe I am the first, who informs you that the following licenses does not work with the
newly available STEP7 PROFESSIONAL 2017 installation media which installs Step7 v5.6 HF1.
STEP7 v5.6 Basis license: WORKS
STEP7 v5.6 Professional license: DOES NOT WORK
STEP7 v14 Professional Combo license: DOES NOT WORK
yes... valid key for STEP7 v14.1 Professional / для STEP7 PROFESSIONAL 2017 подходит ключ от v14.1
see New keys folder / смотрите ключ в папке Новые ключи
Re: [LINK]: STEP 7 V5.6 Professional version 2017
Posted: Thu Aug 31, 2017 8:56 am
by KPPNST
van8x10 wrote:STEP 7 2017 Pro (V5.6) runs very slowly on Windows 10 Pro 64bit ! (version 1703, Build 15063.332)
It runs and works on Windows 10 Enterprise RUS v1703 x64 (15063.540) (i7-4710HQ + 8Gb RAM + SSD 256G) very well and fast.
STEP 7 2017 Pro (V5.6) runs very slowly on Windows 10 Pro 64bit ! (version 1703, Build 15063.332)
Yeah, I've reset my laptop and re-installed the software, and now it works well!
Re: [LINK]: STEP 7 V5.6 HF1 Professional version 2017
Posted: Sat Nov 25, 2017 9:16 pm
by MILSANT2016
friends
Download the software from Step 7 v 5.6 indicated on the page.
When I want to install everything, it is going well until you inform me that Step 7 v5.6 can not be installed because the computer has installed step 7 V5.6 HF1 WHAT IS NOT TRUE WHAT HAPPENS AND PLEASE IF SOMEONE CAN HELP ME
THANK YOU.
Re: [LINK]: STEP 7 V5.6 HF1 Professional version 2017
Posted: Sun Dec 03, 2017 11:09 pm
by MILSANT2016
Dear
A while ago I had a problem with the EKB ESPECIALLY THOSE OF 2017 _8.
I DO ALL THE OPERATIONS THROW THEM IN THE FOLDER
AX NF ZZ BUT DO NOT TAKE THE PROGRAMS.
MY OPERATIVE SYSTEM IS WINDOWS 10 PRO OF 64 BITS.
I INSTALL ANY SIEMENS PROGRAM AND DO NOT ACTIVATE IT WHAT CAN IT BE? NEITHER DOES THE AUTOMATION MANAGER CONNECT THE EKB PROGRAM WHAT CAN I DO? THANK MUCH.
Re: [LINK]: STEP 7 V5.6 HF1 Professional version 2017
Posted: Sat Jan 06, 2018 9:29 pm
by roberto_battistella
you can download hf3 only after opening a ticket to the support request (or I can pass it through we transfer)
Re: [LINK]: STEP 7 V5.6 HF1 Professional version 2017
Posted: Sun Jan 21, 2018 7:52 am
by xflash
roberto_battistella wrote:you can download hf3 only after opening a ticket to the support request (or I can pass it through we transfer)
Please do that or upload to mega. Thank you a lot.
Re: [LINK]: STEP 7 V5.6 HF1 Professional version 2017
What has Changed Compared to Version STEP 7 V5.6 SP1? wrote:
HW Config
· The installation of HSPs is now possible using the command line call via the HSP installer. You can find more information in the help on configuring the hardware in topic "Installing HW Updated via the Command Line".
· The operation of a DP/FF-Link downstream from an IE/PB-Link V3.1 is now possible.
· As of this Hotfix: A configuration in RUN is now once again possible for specific configurations that were downloaded to the CPU with STEP 7 V5.5 SP4 HF9. NetPro
· The output of warnings during compilation in NetPro has been improved. Report System Error
· Generating 'Report System Error' has been improved.
Re: [LINK]: STEP 7 V5.6 SR1 Professional version 2017/2018
Re: [LINK]: STEP 7 V5.6 SR1 Professional version 2017/2018
Posted: Wed Aug 28, 2019 8:34 pm
by Togomi
Hi,
I have to install Step 7 on W10 and I've found Step 7 v5.6 SP1 and Step 7 Professional 2017 SR1.
I checked that Professional includes PLCSIM, S7-GRAPH...
Which one should I install?
v5.6 SP1 requires to install PLCSIM and S7-GRAPH after, doesn't it?
And I've found HF3 and HF5.
Sould I install both or HF5 is enough?
Should I install with v5.6 SP1 and Professional 2017 SR1? Do both require the update?
The most recent EKB I have is from November 2018. Is there another one more recent?
Re: [LINK]: STEP 7 V5.6 SR1 Professional version 2017/2018
Posted: Thu Aug 29, 2019 9:27 am
by Togomi
Thanks.
Do you know if HF3 or HF5 are important? https://support.industry.siemens.com/cs ... /109767446
I had v5.6 in W10 two years ago and Step 7 had problems that required HF's to solve them.
I don't know how Step 7 v5.6 SP1 works on W10 recently.
Greets
Re: [LINK]: STEP 7 V5.6 SR1 Professional version 2017/2018
Posted: Thu Aug 29, 2019 4:18 pm
by Umencho
Step 7 5.6 SP1 is working on WIN10.
Check the projects on which you will work and based on that select the software they will need.
Re: [LINK]: STEP 7 V5.6 SR1 HF5 Professional version 2017/2018
What has Changed Compared to Version STEP 7 V5.6 SP2?
HW Config
• Adding connections via command interface has been improved.
• The configuration of Safety modules via GSD has been improved.
• It is now once again possible to configure I devices in shared mode.
• Restricted use of scripts in the STEP 7 command interface on Windows 10
Due to thread synchronization problems when automatically saving STEP 7 user data, Visual Basic script applications can experience sporadic crashes (possibly with data loss). Therefore, the command interface is currently only partially suitable for such applications. Unpredictable errors can occur, especially with nested loop operations. It is highly recommended that you avoid such use cases and use Visual Basic scripts only with care and caution.
• As of this Hotfix: When uploading certain device configurations, the IP address was corrupted. This has now been corrected.
Programming LAD/STL/FBD blocks
• The function "Check and Update Accesses" has been improved.
Re: [LINK]: STEP 7 V5.6 SR2 Professional version 2017/2020
Posted: Sat Jan 09, 2021 9:26 am
by enea
Hi everybody i just installed on win10 and i have problem with license ,during EKB install it says :(Access violation at address 0040B7CC in module'Sim_EKB_Install_2020_10_10.exe'.Read of address EEF2E0DE.)
Thankyou!
Re: [LINK]: STEP 7 V5.6 SR2 Professional version 2017/2020
Posted: Sat Jan 09, 2021 10:33 am
by CoMod
Hi everybody i just installed on win10 and i have problem with license ,during EKB install it says :(Access violation at address 0040B7CC in module'Sim_EKB_Install_2020_10_10.exe'.Read of address EEF2E0DE.)
EKB file is System Hidden in System Hidden folder C:\AX NF ZZ = for write EKB need Run as Admin
ЕКБ файлы Скрытые Системные в Скрытой Системной папке C:\AX NF ZZ = для их записи надо запускать с полномочиями Администратора
Re: [LINK]: STEP 7 V5.6 SR2 Professional version 2017/2020
Posted: Mon Feb 08, 2021 2:53 pm
by jpm_oliveira
Hello,
I'm try to install license for TIA portal 16 Upd3 with EKB_Install_2020_04_17 (running as administrator on Win10) but it show me the follow error message:
"CryptAcquireContext MS_DEF_PROV Error of containger opening: NTE_BAD_KEYSET"
and a second one:
"CryptAcquireContext PROV_RSA_FULL Error of containger opening: unknown error"
Someone can help me on this matter?
Re: [LINK]: STEP 7 V5.6 SR2 Professional version 2017/2020
Posted: Thu Apr 01, 2021 8:03 am
by pisoj
Anyone can provide with torrent or mega for Hotfix 1 of Step 7 Professional 2017 SR2???