Search found 26 matches

by sandumon84
Sun Apr 14, 2019 3:07 pm
Forum: Allen-Bradley (Rockwell Automation)
Topic: 1746 BAS 502 M0/M1 module
Replies: 0
Views: 450

1746 BAS 502 M0/M1 module

Hi, I am upgrading a AB PLc to Siemens PLC logic and everything is ready for siemens but the problem is the existing PLC is communicating to DCS via modbus RTU as slave. I can see some alarms and data from N10:0 register moving to M0:1.1 with a length of 50 file and from DCS M1:1.1 data moving to re...
by sandumon84
Tue Mar 05, 2019 12:11 pm
Forum: Allen-Bradley (Rockwell Automation)
Topic: Compact PLC error
Replies: 3
Views: 473

Re: Compact PLC error

Hi, I have checked the PLC fault table and could not see any major or minor faults. Also after monitoring the system we found that PLC is going to IO fault because of the festo controller is in fault mode. So whenever we connect both machines in one network either one of the festo controller will go...
by sandumon84
Sat Mar 02, 2019 7:07 am
Forum: Allen-Bradley (Rockwell Automation)
Topic: Compact PLC error
Replies: 3
Views: 473

Re: Compact PLC error

Hi,

Machine manufacturer was checking the diag buffer and he couldnt see any ip conflict however I am at site today and will check the diag buffer and update you...

Regards
Sandeep
by sandumon84
Fri Mar 01, 2019 6:20 pm
Forum: Allen-Bradley (Rockwell Automation)
Topic: Compact PLC error
Replies: 3
Views: 473

Compact PLC error

HI all, I am facing a very strange problem at site,, there are two machines with same ip address which we are trying to connect with our scada. In order to avoid the IP conflict we have changed one of the machines and associated devices IP addresses to a different range to isolate the machine. But w...
by sandumon84
Mon Feb 18, 2019 6:58 am
Forum: OMRON PLC & HMI
Topic: Cj1W-ETN21
Replies: 0
Views: 1082

Cj1W-ETN21

Hi, We have four machines with omron CJ1M-CPU11 PLC's and we purchased CJ1w-etn21 for ethernet communication for 3nos of machines installed and configured, but one of the machines PLC main rack is full so I would like to know the options to solve this like expansion racks or some thing Regards Sandeep
by sandumon84
Thu Jan 03, 2019 8:58 am
Forum: Allen-Bradley (Rockwell Automation)
Topic: AB RSlogix500 timer bit
Replies: 1
Views: 736

AB RSlogix500 timer bit

Hi, As I just upgrading the AB PLC to Siemens PLC I have small doubt regarding the logic In the logic there is a TON timer with 900sec preset and most of the rungs used a bit .ACC/0 bit , when I tried to simulate the logic it is showing blinking like every second. In siemens I believe we can use the...
by sandumon84
Mon Nov 05, 2018 11:32 am
Forum: Allen-Bradley (Rockwell Automation)
Topic: Panelview plus with kepserver
Replies: 0
Views: 953

Panelview plus with kepserver

Hi, We have two identical machines with Panelview plus hmi communicating with Siemens S71200 via kepserver opc. one of the machines hmi not working and we have to replace the HMI. Currently we do have the MER file backup only which is uploaded from the working system. I would like to know if we just...
by sandumon84
Mon Oct 08, 2018 6:59 pm
Forum: Allen-Bradley (Rockwell Automation)
Topic: SLC 504 to SCADA
Replies: 0
Views: 850

SLC 504 to SCADA

HI,

We have an SLC504 PLC which is already connected to an HMI by using RS485 port (DH+) we are tying to install a SCADA to interface with this PLC so I would like to know if its possible to interface the PLC to scada via same port by using DH+ protocol.



Regards
Sandy
by sandumon84
Tue Sep 11, 2018 6:55 pm
Forum: Allen-Bradley (Rockwell Automation)
Topic: Micrologix1500
Replies: 2
Views: 1199

Re: Micrologix1500

Hi,

We are going to use Zenon copadata software it will support AB drivers and modbus tcp/ip also it is capable to poll from PLC

Regards
Sandeep
by sandumon84
Thu Aug 23, 2018 7:21 pm
Forum: Allen-Bradley (Rockwell Automation)
Topic: Allenbradley PLC to modbus TCP/IP
Replies: 4
Views: 1851

Re: Allenbradley PLC to modbus TCP/IP

Hi,

Thanks for the reply I dont think we can replace the ML1500 with 1400 as there are some 1769 type modules connected which may not support by ML1400 hence we are planning to use prosoft DF1 routing module ie PLX51-DF1-ENI. Any feedback would be appreciated

Regards
Sandy
by sandumon84
Sun Aug 19, 2018 5:57 pm
Forum: Allen-Bradley (Rockwell Automation)
Topic: Micrologix1500
Replies: 2
Views: 1199

Micrologix1500

Hi, I have a Micrologix PLC 1500 on which channel 0 is free. I need to take this PLC in scada via ethernet module any one can suggest a suitable module for this?? currently I have searched and found two modules which are 1761-NET ENI prosoft -PLX51-DF1-ENI Which one will be reliable if some one used...
by sandumon84
Fri Aug 17, 2018 6:06 pm
Forum: Allen-Bradley (Rockwell Automation)
Topic: Allenbradley PLC to modbus TCP/IP
Replies: 4
Views: 1851

Re: Allenbradley PLC to modbus TCP/IP

Hi, Thanks for the reply, Right now only Compact logix L35E is having ethernet port. Are you sure micrologix1500 have ethernet port because I could not see any ethernet port in the PLC and I was thinking to convert the PLC to Micrologix 1400. Also SLC5/04 need to use some additional module for ether...
by sandumon84
Fri Aug 10, 2018 1:16 pm
Forum: Allen-Bradley (Rockwell Automation)
Topic: Allenbradley PLC to modbus TCP/IP
Replies: 4
Views: 1851

Allenbradley PLC to modbus TCP/IP

Hi all,

I have three PLC's which I want in modbus TCP/IP. Any one can help?


1.Allen Bradley Compact Logix L35E
2.Allen Bradley SLC 5/04
3.Allen Bradley Micrologix 1500

Regards
Sandeep
by sandumon84
Sat Jul 21, 2018 3:39 pm
Forum: OMRON PLC & HMI
Topic: OMRON-CJ1M-CPU11/CPU12
Replies: 0
Views: 1110

OMRON-CJ1M-CPU11/CPU12

Hi, We have project to monitor machine details in Zenon SCADA. For this we need to establish communication between Omron CJ1m-CPU11 and CPU12 with Zenon ( Zenon supports more than 300 PLC Protocol) . Right now PLC Port2-RS232 already used for HMI I would like to know the best possible way to communi...
by sandumon84
Sat Apr 14, 2018 10:48 am
Forum: Allen-Bradley (Rockwell Automation)
Topic: CLX upgrade
Replies: 0
Views: 1134

CLX upgrade

Hi, We have a control logix plc system with devicenet scanner, ethernet module & control net module there are valve islands communicating via device net protocol and RIO panels via controlnet. Now the CPU memory is almost full and we would like to upgrade the CPU only so I would like to know if it i...
by sandumon84
Mon Nov 13, 2017 5:09 pm
Forum: Allen-Bradley (Rockwell Automation)
Topic: Control logix PLC with ESA HMI
Replies: 0
Views: 1131

Control logix PLC with ESA HMI

Hi experts, We have one control logix plc with ethernet module which is already running for a long time. now we wish to take some data on a remote hmi. we are able to ping the PLC but data is not updating in HMI -it shows some protocol error and the ESA tech people saying this is because our plc is ...
by sandumon84
Thu Aug 04, 2016 8:24 pm
Forum: Other PLC
Topic: ABB dox10 v3.3 or v3.4
Replies: 0
Views: 1162

ABB dox10 v3.3 or v3.4

does any body have this ABB dox 10v3.3 or 3.4 please???
by sandumon84
Wed Jun 22, 2016 7:52 pm
Forum: SIMATIC system
Topic: [?]: S7-300 Siemens PLC DI-96 / DO-64 / AO-8 / AI-24 / HMI
Replies: 3
Views: 3375

Re: [?]: S7-300 Siemens PLC DI-96 / DO-64 / AO-8 / AI-24 / H

I used TIA selection but I would like to know if s7-1500 is a good choice than s7-300...cost also concerned

Sandy
by sandumon84
Mon Jun 20, 2016 12:10 pm
Forum: SIMATIC system
Topic: [?]: S7-300 Siemens PLC DI-96 / DO-64 / AO-8 / AI-24 / HMI
Replies: 3
Views: 3375

[?]: S7-300 Siemens PLC DI-96 / DO-64 / AO-8 / AI-24 / HMI

Hello experts,

Can any one suggest a cost effective system for the following configuration. I wish to use S7-300 am I correct?

CPU-1
DI-96
DO-64
AO-8
AI-24

HMI-with serial communication

Sandy
by sandumon84
Sat Jul 25, 2015 9:16 am
Forum: SIMATIC system
Topic: CPU-315-2DP in fault
Replies: 1
Views: 1716

CPU-315-2DP in fault

Hello Experts, We have a S7 300 PLC ie CPU-315-2D as master and 4 CPU-315-2DP slave plc's.Everything was running perfect till last week and suddenly it went to stop mode. now SYSF indication is constantly red and BUSF is flashing red and CPU mode is stop mode. I have tried to restart the system but ...
by sandumon84
Sat Jan 31, 2015 6:53 am
Forum: SIMATIC system
Topic: [?]: TIA portal v13 and s7-1200 with TIA 11/12
Replies: 6
Views: 7431

Re: [?]: TIA portal v13 and s7-1200 with TIA 11/12

Hi

I tried to download the torrent but after registering no response
by sandumon84
Wed Jan 28, 2015 8:51 am
Forum: SIMATIC system
Topic: [?]: TIA portal v13 and s7-1200 with TIA 11/12
Replies: 6
Views: 7431

Re: [?]: TIA portal v13 and s7-1200 with TIA 11/12

Can any body share TIA Portal V11 link

I searchd a lot but no success
by sandumon84
Sun Jan 25, 2015 9:49 am
Forum: SIMATIC system
Topic: [?]: TIA portal v13 and s7-1200 with TIA 11/12
Replies: 6
Views: 7431

Re: [?]: TIA portal v13 and s7-1200 with TIA 11/12

Hi, Thanks for the info I have installed TIA portal v12 SP1 so when I tried to upload from the controller (S71200) I got error " Project inside controller is v11 and incompatible etc) So I downloaded the compatibility mode project from siemens support site and uploaded successfully now my doubt is w...
by sandumon84
Wed Jan 21, 2015 9:10 am
Forum: Allen-Bradley (Rockwell Automation)
Topic: Panelview plus6 1000 HMI tag
Replies: 2
Views: 2311

Re: Panelview plus6 1000 HMI tag

Thank you nowan

appreciated your way of explanation

Thanks again
by sandumon84
Wed Jan 21, 2015 9:09 am
Forum: SIMATIC system
Topic: [?]: TIA portal v13 and s7-1200 with TIA 11/12
Replies: 6
Views: 7431

[?]: TIA portal v13 and s7-1200 with TIA 11/12

Hi expertz, I have two query A>I am a fresher to siemens step7 . I have installed TIA portal v13 in my laptop . We have a customer who is having Simatic s7 1200 controller so I need to upload the program from the device. The problem is customer have no idea who downloaded or which version of step 7...
by sandumon84
Sun Dec 28, 2014 4:54 pm
Forum: Allen-Bradley (Rockwell Automation)
Topic: Panelview plus6 1000 HMI tag
Replies: 2
Views: 2311

Panelview plus6 1000 HMI tag

Hi experts,

I have just got an HMI backup. When I am checking some display parameters I found some tag like "#1.ch0data" I would like to know what is it meant by as I am new to rockwell please give me some ideas.

Thanks
sandy